LON & SUR
24/7
All Advice
Carpentry

Hanging a New Internal Door: What the Job Involves

The CS Services Carpentry Team12 October 2026 7 min read
Hanging a New Internal Door: What the Job Involves

A new internal door can make a room feel finished, quieter and more private, but fitting one properly is rarely a simple swap. In many London and Surrey homes, the opening is older than the door, the frame is out of square and the floor levels have changed over time.

That is why door hanging is a skilled carpentry job rather than a quick DIY task. If you understand what is being checked and adjusted before the door goes on, you are far less likely to end up with sticking edges, uneven gaps or a latch that never quite catches.

Why new doors rarely fit straight away

Most new internal doors are supplied slightly oversize because openings vary from house to house. Even where the nominal size matches, older linings can lean, twist or narrow slightly at one point, especially in period terraces, converted flats and properties where plaster, flooring or skirting has been replaced more than once.

Before any cutting starts, the opening needs to be measured in several places, not just once. A good check includes the width at top, middle and bottom, the height on both sides, the diagonal measurement to see if the frame is square, and the floor clearance needed for carpet, underlay or hard flooring.

Homeowners can do some useful early checks themselves. Look for rub marks on the old door, uneven gaps around the frame, a latch that needs lifting to close, or a door that swings open by itself, as these all suggest frame or hinge issues that need allowing for.

  • Measure the opening more than once and in more than one place
  • Check whether new flooring is planned before the door is trimmed
  • Look at the condition of the lining, hinges and latch keep, not just the door leaf
  • Allow for access and manoeuvring space in tight hallways and staircases

Trimming, hinging and latching

Once the door size is confirmed, trimming has to be done carefully and evenly. Taking too much from one side can throw off the appearance, weaken the edge or leave the latch stile too narrow, and some factory-finished or veneered doors have strict trimming limits that should be checked before any cut is made.

Hinges then need accurate marking and neat recessing so they sit flush. If the hinge positions do not match properly, the door can bind, drop over time or leave inconsistent gaps at the head and sides.

The latch side needs the same level of care. The latch must line up cleanly with the keep, the handle height should suit the existing doors in the property where possible, and the strike point must be set so the door closes securely without rattling or needing to be slammed.

  • You can safely confirm handle height preferences and door swing before work starts
  • You can remove nearby pictures, rugs and breakables to give clear working space
  • Leave trimming, hinge recesses and latch mortices to a professional if you want a clean finish
  • If you are reusing old ironmongery, check that all parts are complete and not badly worn

Fire doors and building requirements

Fire doors are not just heavier versions of standard internal doors. They are part of a tested assembly, and how they are fitted matters just as much as the door itself, including the frame condition, intumescent strips, hinges, glazing where relevant and the size of the perimeter gaps.

This is particularly important in flat conversions, loft conversions and some newer developments around London and Surrey, where compartmentation and escape routes are a bigger issue. Replacing a door with the wrong type, over-trimming it or fitting unsuitable hardware can compromise performance and may create problems when the property is sold or inspected.

If you think a door may be a fire door, do not assume it can be treated like an ordinary bedroom or cupboard door. Ask for the specification to be checked first, especially if the existing door leads onto a shared hallway, stair enclosure, integral garage or protected route.

  • Do not plane a suspected fire door without confirming its permitted trimming limits
  • Check whether self-closers, smoke seals or intumescent strips are required
  • Keep any labels, certification and product information for future records
  • Call a professional if the door is in a flat, conversion or other regulated escape route

Handles, stops and the final finish

A door can be perfectly hung and still feel wrong if the final details are poor. Handles should be level, secure and comfortable to use, and the latch should engage cleanly without excessive pressure or play.

Door stops often need minor adjustment as part of the job, particularly where old doors were warped and the frame was made to suit them. In decorated rooms, careful planning matters because any trimming, stop adjustment or hardware changes can expose bare timber, old paint lines or filled fixing holes that need making good.

In compact London homes and many flat conversions, opening direction also matters more than people expect. A door that clashes with a radiator, wardrobe, light switch or narrow landing can be inconvenient every single day, so it is worth deciding this before the hinges are cut in.

  • Decide early whether the door should open left or right handed
  • Check for clashes with radiators, furniture, sockets and switches
  • Expect some making good if replacing old hardware or altering stops
  • Ask about finishing requirements if the door arrives unfinished or pre-primed

When to get professional carpentry help

Simple tasks such as choosing the door style, confirming swing direction and clearing access are realistic for most homeowners. The skilled part is getting the fit right in a frame that is rarely perfect, while protecting floors, walls and the door finish at the same time.

Professional help is usually the better option where the frame is out of square, the door is a fire door, the floor level is changing, or several doors need to match through the house. This is also true in older properties where nothing is quite standard and in homes with limited parking or on-street access, where a well-planned visit avoids delays and repeat work.

CS Services is currently advertising carpentry as coming soon, with enquiries welcome ahead of launch. If you are planning internal door work in London or Surrey, it is sensible to raise the job early so the opening, door type and hardware can be scoped properly before fitting day.

Key Takeaways

  • New internal doors usually need measuring and trimming to suit the opening.
  • Uneven frames and altered floors are common in London and Surrey homes.
  • Hinges and latches need precise setting for smooth closing and even gaps.
  • Fire doors have specific fitting requirements and should not be treated as standard doors.
  • Clear decisions on swing, handles and finishing prevent awkward daily use.

Frequently Asked Questions

Can I buy a door myself and just ask someone to hang it?

Yes, but check the exact size, construction and finish first. It helps to confirm the opening measurements and any trimming limits before you buy, as some doors allow only limited material to be removed from the edges.

How do I know if my frame needs attention as well as the door?

Look for uneven gaps, sticking points, a latch that misses the keep, cracked hinge areas or a frame that visibly leans. If the old door only works when lifted or pushed hard, the frame or ironmongery may need adjustment too.

Can I trim the bottom of a door after new carpet is fitted?

Sometimes, but it is better to plan for the finished floor level in advance. Cutting after fitting can be awkward and may affect the appearance or, on some doors, exceed the manufacturer’s trimming allowance.

Are fire doors really that different to fit?

Yes. The door, gaps, hinges, seals and frame condition all matter, and the installation has to preserve the fire performance of the assembly. If there is any doubt, treat it as a specialist job.

Is carpentry available to book with CS Services now?

Not yet. Carpentry is currently advertised as coming soon, and enquiries are welcome ahead of launch for planned work in London and Surrey.

Carpentry Across London & Surrey

Our engineers cover homes right across London and Surrey. Explore our carpentry service in these areas:

Need A Hand With The Real Thing?

Our certified, insured engineers cover London and Surrey. No call-out fees, card on completion and a 12-month guarantee on our work.