LON & SUR
24/7
All Advice
Plumbing

Frozen Pipes: How to Thaw Them Safely and Prevent Bursts

The CS Services Plumbing Team18 November 2026 6 min read
Frozen Pipes: How to Thaw Them Safely and Prevent Bursts

Frozen pipework is one of the most disruptive winter plumbing problems in London and Surrey homes. It often starts quietly, with reduced flow at a tap or a toilet that refills slowly, then becomes a much larger issue if the pipe splits as the ice expands.

The risk is higher in older properties, loft spaces, rear extensions, garages, cupboards on outside walls and flat conversions where pipe runs may have been added into awkward spaces. Many homeowners can take sensible first steps themselves, but it is important to thaw pipes carefully and know when to stop.

This guide covers where pipes usually freeze first, how to thaw them safely, what not to do and the practical prevention work that makes a real difference before cold weather sets in.

Which pipes freeze first

Pipes freeze where they are exposed to the cold for longest and have the least protection around them. In practice, that usually means pipework in lofts, garages, under kitchen floors, inside unheated outbuildings, behind boxing on external walls and beneath sinks in little-used rooms.

In London and Surrey, period homes and converted flats often have altered layouts, patched-in pipe runs and older insulation standards. Rear kitchen extensions, side returns and pipes routed through cupboards against outside walls are common weak points, especially where there are draughts.

If only one tap has stopped working, the frozen section is likely to be on the branch serving that fitting. If several cold taps are affected, or the incoming supply seems slow throughout the property, the frozen section may be closer to where the main pipe enters the home.

  • Look for reduced water flow, not just a complete loss of water
  • Check toilets that refill slowly or stop refilling altogether
  • Notice any unusual damp patches, staining or bulging pipe insulation
  • Listen for odd sounds such as knocking or gurgling when you try a tap
  • Pay extra attention to pipes in lofts, under stairs cupboards and external utility spaces

How to thaw a frozen pipe safely

Start by finding the frozen section as accurately as you can. Frost on the pipe, a very cold patch, or a section that feels colder than the surrounding run can help you narrow it down, but do not pull off fixed coverings aggressively just to inspect it.

Before you apply any heat, turn off the water at the internal stop tap if you suspect the pipe may already have cracked. Then open the affected tap slightly so melted water and pressure can escape as the ice thaws.

  • Apply gentle warmth to the pipe using towels soaked in warm water, a hot water bottle, or a hairdryer on a low setting
  • Warm the pipe gradually, starting at the end nearest the tap and working back towards the colder section
  • Keep checking for leaks as the ice melts and water starts moving again
  • If the pipe is boxed in, warm the surrounding air carefully rather than forcing heat into a hidden void
  • Once flow returns, leave the tap running lightly for a short time and check nearby joints and fittings

What never to do

Burst pipes often happen during bad thawing attempts rather than during the freeze itself. Sudden, intense heat can damage pipework, soften plastic fittings and cause a hidden split to open up quickly.

Do not take risks with electrics or improvised heat sources, especially in tight cupboards, lofts and under-sink spaces. These areas often contain combustible materials, old boxing, stored items and poor ventilation.

  • Do not use a blowtorch, gas heater or naked flame
  • Do not pour boiling water directly onto pipework or fittings
  • Do not use portable electrical heaters in wet or cramped areas
  • Do not keep forcing taps if you suspect the pipe is blocked with ice
  • Do not ignore a small crack or drip once the pipe starts to thaw

When to call a plumber

Call a professional if you cannot find the frozen section, if the pipe is inaccessible, or if you suspect it has already split. Water marks, leaking joints, bulging ceilings below a bathroom or loft, and a loss of pressure after thawing all point to damage that needs proper attention.

A plumber is also the right next step where freezing keeps happening in the same place. That usually means the route, insulation or support of the pipework needs improving rather than just another temporary thaw.

CS Services provides plumbing across London and Surrey, with transparent pricing and no call-out fee. Plumbing is charged from £140 per hour, with the price agreed before work begins.

Lagging and prevention that actually works

The best prevention is to protect vulnerable pipe runs before freezing weather arrives. Basic lagging helps, but it is only effective if it is fitted properly and the full exposed run is covered, including bends, valves and awkward short sections that often get missed.

Prevention matters particularly in homes with small side returns, loft conversions, garden outbuildings and older external walls. Hard water in London and Surrey can also leave scale inside pipework and fittings over time, which makes good maintenance worthwhile even though limescale itself is not the cause of freezing.

  • Insulate exposed pipes in lofts, garages, cupboards on external walls and under floors where accessible
  • Seal draughts around pipe entry points, especially under sinks and inside utility cupboards
  • Repair dripping taps and faulty valves, as small water issues can make winter pipe problems harder to manage
  • Keep background heating on during cold snaps, particularly if the property will be empty
  • Open cupboard doors occasionally in very cold weather to let warmer air circulate around pipework
  • Know where your stop tap is and make sure everyone in the household can turn it off quickly

Key Takeaways

  • Pipes usually freeze first in unheated or poorly insulated areas.
  • Thaw pipes slowly with gentle warmth, never intense heat.
  • Open the affected tap slightly while thawing to relieve pressure.
  • If a pipe may have split, turn the water off before thawing further.
  • Proper lagging and draught reduction are the most reliable prevention steps.

Frequently Asked Questions

How do I know if a pipe is frozen or blocked?

A frozen pipe is more likely during very cold weather and often follows a sudden drop in flow or no water at one or more taps. A blockage is more likely to affect drainage rather than the incoming water supply, although a plumber may be needed if the cause is not clear.

Should I turn the water off if I think a pipe is frozen?

If you suspect the pipe may have cracked, or you see damp patches or dripping, turn the water off at the stop tap straight away. If there is no sign of a split, you can begin careful thawing while monitoring the pipe closely.

Can frozen pipes burst later, after the ice has thawed?

Yes. A pipe can split while frozen and only start leaking properly once water begins flowing again. That is why you should check the pipe and nearby areas carefully during and after thawing.

Are plastic pipes less likely to freeze than copper pipes?

Both can freeze if they are exposed to cold conditions. Plastic may tolerate expansion differently, but it still needs proper insulation and a sensible pipe route.

What should I do if I am away from home during freezing weather?

Leave background heating on, ask someone to check the property if possible, and make sure you know how the water can be isolated if there is a problem. Vulnerable pipes in lofts, garages and extensions should be insulated well before winter.

Plumbing Across London & Surrey

Our engineers cover homes right across London and Surrey. Explore our plumbing service in these areas:

Need A Hand With The Real Thing?

Our certified, insured engineers cover London and Surrey. No call-out fees, card on completion and a 12-month guarantee on our work.